- 您现在的位置：买卖IC网 > Sheet目录402 > CTSR 0.6-TP (LEM USA Inc)TRANSDUCER CURRENT 0.6A
CTSR 0.6-TP/SP2
Assembly on PCB
● Recommended PCB hole diameter
Maximum PCB thickness
● Wave soldering profile
1.2 mm for secondary pin
2.9 mm for primary pin
2.4 mm
maximum 260 °C, 10 s
No clean process only
Any primary conductor must be placed in the PCB at the requested insulation distance regarding the secondary side (see also
paragraph “Insulation around the CTSR transducer housing”).
Definition of typical, minimum and maximum values
Minimum and maximum values for specified limiting and safety conditions have to be understood as such as well as values shown
in “typical” graphs. On the other hand, measured values are part of a statistical distribution that can be specified by an interval with
upper and lower limits and a probability for measured values to lie within this interval.
Unless otherwise stated (e.g. “100 % tested”), the LEM definition for such intervals designated with “min” and “max” is that the
probability for values of samples to lie in this interval is 99.73 %. For a normal (Gaussian) distribution, this corresponds to an
interval between -3 sigma and +3 sigma.
If “typical” values are not obviously mean or average values, those values are defined to delimit intervals with a probability of 68.27
%, corresponding to an interval between -sigma and +sigma for a normal distribution.
Typical, maximal and minimal values are determined during the initial characterization of a product.
Safety
This transducer must be used in limited-energy secondary circuits according to IEC 61010-1.
This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements in
accordance with the manufacturer ’s operating instructions.
Caution, risk of electrical shock
When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply).
Ignoring this warning can lead to injury and/or cause serious damage.
This transducer is a build-in device, whose conducting parts must be inaccessible after installation.
A protective housing or additional shield could be used.
Main supply must be able to be disconnected.
Page 9/10
28January2014/version 6
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice
www.lem.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
CWF1B104G3950
THERMISTOR NTC -+2% 3950K PROBE
CX11352_LAURA-RS
LENS FOR LUXEON REBEL
D6F-02L2-000
SENSOR GAS FLOW TYPE 0-2L/MIN
D6F-05N7-000
SENSOR MICRO-FLOW
D6F-CABLE1
CABLE FOR MEMS FLOW SENSOR
D6F-CABLE2
CABLE FOR D6F MASSFLOW SENSOR
D6F-P0010A2
SENSOR AIRFLOW 0-50KPA W/CONN
D6F-V03A1
AIRFLOW SENSOR 0-3 M/SEC 3.3V
相关代理商/技术参数
CTSR 0.6-TP/SP2
功能描述:Current Sensor 600mA 1 Channel Flux Gate, Closed Loop Bidirectional Module 制造商:lem usa inc. 系列:CTSR 包装:散装 零件状态:过期 用于测量:AC/DC 传感器类型:磁通量闸门，闭环 电流 - 检测:600mA 通道数:1 输出:比率，电压 灵敏度:- 频率:9.5kHz 线性度:±0.4% 精度:±1.5% 电压 - 电源:4.75 V ~ 5.25 V 响应时间:30μs 电流 - 电源（最大值）:21.6mA 工作温度:-40°C ~ 105°C 极化:双向 安装类型:PCB，通孔 封装/外壳:模块 标准包装:25
CTSR-1
制造商:ITW Chemtronics 功能描述:Chemical,Silicone Conformal Coating,1 gallon 制造商:ITW Chemtronics 功能描述:CHEMICAL COATING, 1GAL, Coating Type:Conformal, Series:Konform SR, Chemical Colo
CTSR-12
功能描述:化学物质 RoHS:否 制造商:3M Electronic Specialty 产品:Adhesives 类型:Epoxy Compound 大小:1.7 oz 外壳:Plastic Tube
CTSR-HV1
制造商:ITW Chemtronics 功能描述:pail or bottle // 1 gallon
CTSS0000
制造商:Red Lion Controls 功能描述:CURRENT SWITCH, SPLIT CASE 制造商:Red Lion Controls 功能描述:CURRENT SWITCH SPLIT CASE 制造商:Red Lion Controls 功能描述:CURRENT SWITCH,SPLIT CASE
CTS-S12/12
制造商:DEUTSCH CONNECTORS 功能描述:Cross Referenced to DEUTSCH CONNECTORS - Part: DCHM39029/22-605
CTS-S16/16
制造商:TE Connectivity / Deutsch 功能描述:81711 CON socket
CTS-S20/20
制造商:DEUTSCH CONNECTORS 功能描述:Cross Referenced to DEUTSCH CONNECTORS - Part: DCHM39029/22-192